EliteTM SupDual PurposeVacuum CleanerRReviewthis manualbefore0 eratingPc eaner
Align opening in paper bag withdirt tube inside bag compart-ment. (Fig. 19)Push bag collar firmly onto dirttube. (Fig. 20)Tuck top and bottom of bag i
(some models only)Insert hose connector into sideof rack. (Fig. 23)ST---lPosition wand in side of toolrack and snap into place.(Fig. 25)While wrapping
The assembled cleaner will looklike the drawing below.L.111. Handle2. Cord hooks: wrap cordaround hooks for storage. The tophook can be rotated right
w to useTo reduce the risk of electricshock, this appliance has apolarized plug (one blade is widerthan the other). This plug will fit ina polarized o
Carpet heiadjustmentThe cleaning of carpet and rugstakes place at the nozzle.It is necessary to raise and lowerthe nozzle for various carpet pileheigh
The Hoover Company101 East Maple StreetNorth Canton, OH 44720No. of ItemsOrdered:Please complete this entire form!a4010001A0160147AG0 4010324A0049258A
Gleaming lightweightflexible rugsStand on one end of rug and movecleaner toward other end or edge.Before reaching edge, push downon handle. This will
leaning toSome models come with tools; forothers, tools are available atadditional cost from your Autho-rized Hoover Dealer (Depot), aHoover Factory S
HOSE DOORI \\ \and toolsThe tools are attached to the hoseor the wand in the same manner.Push tool firmly onto hose; twist toolslightly to tighten or
during assembly or operation,call1-8OWM4-9200 for an automated referral of authorized serviceoutlet locations (U.S. only) orl-216-499-9499 to speak wi
The bagWhem to replaceCheck bag from time to time. It is recommended that you change thepaper bag when dirt reaches the dotted line. If more dirt than
Note:not clean out old bagand reuse. Discard used bag.Align opening in new paper bagwith dirt tube in outer bag. Pushbag collar firmly onto dirt tube.
2. Place handle in operatingposition and turn cleaner over.Insert end of flat screwdriver intoone of the four slots beside anarrow on bottom of cleane
The belt on your HOOVER cleaner causes the agitator to rotate and isimportant for the effective operation of the cleaner. The belt is locatedunder the
4. If belt is not broken, pull it off themotor pulley.5. Return cleaner to bottom side up.Remove agitator and belt.6. Slip agitator through new belt(w
8. Turn cleaner over and stretchnew belt onto motor pulley.Extra effort may be required tostretch belt onto pulley.9. Replace hood and nozzle controlk
If you have a probleThis appliance was inspected thoroughly and was in good operatingcondition when it was shipped from the factory. If a minor proble
To obtain approved HOOVER service and genuine HOOVER parts,locate the nearest Hoover Factory Service Center or AuthorizedHoover Warranty Service Deale
Full One Year Warranty(Domestic Use)Your HOOVER@ appliance is warranted in normal household use, inaccordance with the Owner’s Manual against original
26
Important Safeguards!When using an electrical appliance, always followbasic precautions, including the following:READ ALL INSTRUCTIONS BEFORE USING TH
Hoover and0(Iare registered trademarksTHE HOOVER COMPANY, NORTH CANTON, OHIO 44720R6 3-95 MO35930/43-930/71-930/75-930Litho USA5651 l-396
mbling cleanersextremelyimportamt to read and ifUow a01 the instruction steps in order.The assembled cleaner will look likethis drawing.If you need as
LOWER HANDLEPlace upper and lower handle sections on a flat surface with cordhooks on top. With hands on sides of handle sections, push sectionstogeth
IIRotate cord protector on cord until you see its arrow. (Fig. 4)-,---,ARROW&- CoRD pROTECTORUPPERHANDLEWith arrow on cord protectorpointing towar
RAILSRAILSNote location of tapered railson bracket and on lowerhandle. (Fig. 8)With printed side of bracketfacing up, slide rails on bracketonto rails
I\ IIHook tool rack over left edge of‘handle, matching arrows andletters. (Fig. 11)With cord hooks to the back,place assembled handle ontohandle base
1BAG COMiikl’MENThLOTS’ DIRTTUBEPlace nut in recessed area atback of handle. Hold nut inplace while tightening boltsecurely with a screwdriver.(Fig. 1
Comments to this Manuals